FreeWeldingForum.com 
Welding Forum Community presented by LONGEVITY
877 - Long - Inc | 877.566.4462
Page 3 of 27 FirstFirst 1234513 ... LastLast
Results 21 to 30 of 262

Thread: rocko is going under the knife

  1. #21
    Authorized Longevity Dealer dzljon's Avatar
    Join Date
    Nov 2014
    Location
    Jacksonville Florida
    Posts
    571
    Pulled the gear off the old cam, which was kind of a pain, put it on the grill till well done and transfered to the new shaft and let cool
    Attached Images Attached Images     
    Machines:


    LONGEVITY 250EX 25' WELDCRAFT CS310 TORCH
    LONGEVITY FORCECUT 62i

    TORCHMATE w/ FLASH CUT CNC controls

  2. #22
    Authorized Longevity Dealer dzljon's Avatar
    Join Date
    Nov 2014
    Location
    Jacksonville Florida
    Posts
    571
    Rocko specs
    stock engine: 4.0l
    trans: nv3550
    axles: dana 30 and 35
    gears 3.07
    Suspension: stock for now
    tires: 245/75r16 goodyear mtr, new, getting g replaced
    milage: 118xxx
    transfer case:np231

    Diesel conversion
    4bt cummins
    105hp @ 2500

    Ported and polished head, new valves, guides and springs
    center mounted he341 turbo from 2004 5.9l
    modified exhaust manifold
    ceramic coated pistons
    stage 1 camshaft
    40hp injectors
    3200 gov spring
    upgraded fuel pin

    Projected power 175 hp 400 tq
    28+ mpg in the little jeep
    Last edited by dzljon; 04-29-2015 at 09:07 PM.
    Machines:


    LONGEVITY 250EX 25' WELDCRAFT CS310 TORCH
    LONGEVITY FORCECUT 62i

    TORCHMATE w/ FLASH CUT CNC controls

  3. #23
    Authorized Longevity Dealer dzljon's Avatar
    Join Date
    Nov 2014
    Location
    Jacksonville Florida
    Posts
    571
    Added a new sticker
    Attached Images Attached Images  
    Machines:


    LONGEVITY 250EX 25' WELDCRAFT CS310 TORCH
    LONGEVITY FORCECUT 62i

    TORCHMATE w/ FLASH CUT CNC controls

  4. #24
    Authorized Longevity Dealer dzljon's Avatar
    Join Date
    Nov 2014
    Location
    Jacksonville Florida
    Posts
    571
    Picked up the block today, I only had it cleaned up and a light hone and the cam bearing installed, yep that is not a typo there is 1 cam bearing in this engine that runs for 300k miles
    Attached Images Attached Images  
    Last edited by dzljon; 05-01-2015 at 06:10 PM.
    Machines:


    LONGEVITY 250EX 25' WELDCRAFT CS310 TORCH
    LONGEVITY FORCECUT 62i

    TORCHMATE w/ FLASH CUT CNC controls

  5. #25
    Authorized Longevity Dealer dzljon's Avatar
    Join Date
    Nov 2014
    Location
    Jacksonville Florida
    Posts
    571
    Goofing around with pictures
    Attached Images Attached Images  
    Machines:


    LONGEVITY 250EX 25' WELDCRAFT CS310 TORCH
    LONGEVITY FORCECUT 62i

    TORCHMATE w/ FLASH CUT CNC controls

  6. #26
    Authorized Longevity Dealer dzljon's Avatar
    Join Date
    Nov 2014
    Location
    Jacksonville Florida
    Posts
    571
    Installing the pistons
    Attached Images Attached Images    
    Machines:


    LONGEVITY 250EX 25' WELDCRAFT CS310 TORCH
    LONGEVITY FORCECUT 62i

    TORCHMATE w/ FLASH CUT CNC controls

  7. #27
    Authorized Longevity Dealer dzljon's Avatar
    Join Date
    Nov 2014
    Location
    Jacksonville Florida
    Posts
    571
    Moving forward and letting hardware soak
    Attached Images Attached Images   
    Machines:


    LONGEVITY 250EX 25' WELDCRAFT CS310 TORCH
    LONGEVITY FORCECUT 62i

    TORCHMATE w/ FLASH CUT CNC controls

  8. #28
    Authorized Longevity Dealer dzljon's Avatar
    Join Date
    Nov 2014
    Location
    Jacksonville Florida
    Posts
    571
    Getting closer
    Attached Images Attached Images  
    Machines:


    LONGEVITY 250EX 25' WELDCRAFT CS310 TORCH
    LONGEVITY FORCECUT 62i

    TORCHMATE w/ FLASH CUT CNC controls

  9. #29
    Authorized Longevity Dealer dzljon's Avatar
    Join Date
    Nov 2014
    Location
    Jacksonville Florida
    Posts
    571
    This is the airride suspension under my f250
    Attached Images Attached Images     
    Machines:


    LONGEVITY 250EX 25' WELDCRAFT CS310 TORCH
    LONGEVITY FORCECUT 62i

    TORCHMATE w/ FLASH CUT CNC controls

  10. #30
    Authorized Longevity Dealer dzljon's Avatar
    Join Date
    Nov 2014
    Location
    Jacksonville Florida
    Posts
    571
    Repairing ac lines on my f250 powered by a cummins
    Attached Images Attached Images  
    Machines:


    LONGEVITY 250EX 25' WELDCRAFT CS310 TORCH
    LONGEVITY FORCECUT 62i

    TORCHMATE w/ FLASH CUT CNC controls

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •