FreeWeldingForum.com 
Welding Forum Community presented by LONGEVITY

Search:

Type: Posts; User: Gadget

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Thread: Hello!

    by Gadget
    Replies
    1
    Views
    186

    Welcome to the forum Greg. Dan

    Welcome to the forum Greg.

    Dan
  2. Replies
    1
    Views
    362

    Cool projects. The aluminum beads are pretty nice...

    Cool projects. The aluminum beads are pretty nice for someone just learning AL.
  3. Thread: Newbie

    by Gadget
    Replies
    2
    Views
    395

    Hi Eyedoc and welcome to the forum. Dan

    Hi Eyedoc and welcome to the forum.
    Dan
  4. Replies
    6
    Views
    8,118

    This is a 5 year old post by the user with links...

    This is a 5 year old post by the user with links to external photos. The external photos have most likely been deleted or moved at the external site. No way for us to correct the links.
  5. Replies
    2
    Views
    593

    I think the Innovator 255i is the replacement for...

    I think the Innovator 255i is the replacement for the Weldall 200 & 256pi. I'll send an email to Simon to see if they are planning any new lines.
  6. Sticky: Apparently the address the link points to is no...

    Apparently the address the link points to is no longer valid, it used to work.
  7. Thread: New Memeber

    by Gadget
    Replies
    2
    Views
    830

    Hi Dave and welcome to the forum. Dan

    Hi Dave and welcome to the forum.
    Dan
  8. Replies
    4
    Views
    1,097

    Hi Rich and welcome to the forum. The metal...

    Hi Rich and welcome to the forum.
    The metal looks clean enough to weld but the last photo is troubling to me. Trying to build up the thin area cleaned would take a lot of heat and wouldn't be an...
  9. Replies
    2
    Views
    837

    Hi Andrea, The inert gas used in MIG welding is...

    Hi Andrea,
    The inert gas used in MIG welding is usually a mixture of Argon and CO2. The CO2 is mixed usually about 25% Argon 75%. For aluminum welding sometimes Helium is used. The inert gas...
  10. Replies
    1
    Views
    594

    Hi and welcome. I found a link for torch parts...

    Hi and welcome. I found a link for torch parts for your unit. Since they know what parts the torch takes they should know the torch ID and starting technology. Might be worth sending them an email...
  11. Thread: MIG welding

    by Gadget
    Replies
    1
    Views
    615

    For welding steel a mix of argon and CO2 is used....

    For welding steel a mix of argon and CO2 is used. Usually C20 or C25 mix. For aluminum straight argon or argon helium mix is used.
    Hope this helps.
  12. Thread: Got me a 200SX!

    by Gadget
    Replies
    1
    Views
    729

    Hi and welcome to the forum. Looks like you have...

    Hi and welcome to the forum. Looks like you have some fun projects planned, hopefully you'll post some of your work as you progress.
    Dan
  13. Replies
    2
    Views
    645

    Hi Gooseaa88 and welcome to the forum. I use...

    Hi Gooseaa88 and welcome to the forum. I use both a WP80 machine torch and a hand torch depending on what I want to do. My WP80 has a fairly large kerf so if I want to cut fine detail I use the hand...
  14. Run a continuity test with an ohm meter between...

    Run a continuity test with an ohm meter between the hot lead connection at the plug of the spool gun to the tip of the spool gun, I'll bet there is a break somewhere along the line.
  15. Does the welder work when you run it without the...

    Does the welder work when you run it without the spool gun? If so I suspect your cable has a break in it or possibly a bad internal connection on the hot lead.
  16. Replies
    4
    Views
    1,737

    Hi Mrlarrycop and welcome to the forum. New user...

    Hi Mrlarrycop and welcome to the forum. New user posts are moderated to prevent spam. I've approved your initial post and promoted you to registered user so your posts from now on should appear...
  17. Replies
    109
    Views
    224,339

    Rossi, Tom sells the plans but I haven't seen him...

    Rossi, Tom sells the plans but I haven't seen him on here for awhile now.
  18. Replies
    2
    Views
    713

    Welcome to the forum Mark. I would send an email...

    Welcome to the forum Mark. I would send an email to either Daniel or Carlos at Longevity, they've helped others make the proper connections.
    Dan
  19. Thread: New member

    by Gadget
    Replies
    2
    Views
    809

    Hi Bud and welcome to the forum. The gate project...

    Hi Bud and welcome to the forum. The gate project sounds like a lot of fun. Be sure to post some photos and your progress as you go forward with it.
    Dan
  20. Thread: No Arc

    by Gadget
    Replies
    1
    Views
    1,551

    The ground wire should connect to the utility...

    The ground wire should connect to the utility neutral, that is connected to earth ground as well at the utility input.
  21. Replies
    3
    Views
    1,134

    That's quite the base you've got there. Nice...

    That's quite the base you've got there. Nice project.
  22. Replies
    4
    Views
    1,243

    Hi Steve and welcome to the forum. Welding is...

    Hi Steve and welcome to the forum. Welding is always the most satisfying part of my projects, I can understand how you feel.
    Dan
  23. Replies
    7
    Views
    2,100

    Impressive build so far thanks for sharing.

    Impressive build so far thanks for sharing.
  24. I finally finished resoldering all the...

    I finally finished resoldering all the connections on the 200PI main circuit board. Unfortunately that didn't fix the problem so it is now officially a parts machine. As I said earlier though, I...
  25. Replies
    7
    Views
    2,100

    This is getting interesting, nice progress. I'm...

    This is getting interesting, nice progress.
    I'm about to get started on making my plastic shredder, I'm going to document the process and will be posting on the forum shortly.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4