FreeWeldingForum.com 
Welding Forum Community presented by LONGEVITY

Search:

Type: Posts; User: Cope

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    21
    Views
    11,948

    On the HTP 600? I know for a fact it uses the...

    On the HTP 600? I know for a fact it uses the same consumables as the 42i.
  2. Replies
    21
    Views
    11,948

    Gamble, I meant to say that Tecmo makes a PT80. ...

    Gamble, I meant to say that Tecmo makes a PT80. I am well aware that HTP uses the PT60. FWIW, I don't look at the Everlast forum. Looks like the 600 uses the PT60, but the torch on the 875 is...
  3. Replies
    4
    Views
    6,809

    Mart, if it has a pilot start, it is not HF. If...

    Mart, if it has a pilot start, it is not HF. If your torch is complete, it is simple enough to determine which type.
  4. Replies
    21
    Views
    11,948

    The PT-60 is made by Tecmo, and is also used by...

    The PT-60 is made by Tecmo, and is also used by HTP on their Plasma cutter. They also make a PT-80. It is a good torch. I can see how the original failure might have been considered user error,...
  5. Replies
    21
    Views
    11,948

    Not if you also have a hand torch.

    Not if you also have a hand torch.
  6. Thread: Stickweld 200

    by Cope
    Replies
    3
    Views
    3,100

    Should be a NEMA 6-50 as in this link. This is...

    Should be a NEMA 6-50 as in this link. This is the standard 50 amp for welders, even those that require less line amperage.

    https://weldingsupply.com/cgi-bin/einstein.pl?PNUM::1:UNDEF:X:0042

    If...
  7. Replies
    8
    Views
    4,059

    Very nice.

    Very nice.
  8. Replies
    5
    Views
    3,548

    Daniel is Longevity's best kept secret for sure.

    Daniel is Longevity's best kept secret for sure.
  9. My LWS would upgrade for $35, but in January...

    My LWS would upgrade for $35, but in January they became Praxair, and they don't let you upgrade either.
  10. IIRC, they use a different valve on C)2 tanks. ...

    IIRC, they use a different valve on C)2 tanks. You would probably be just about as well off keeping the 80 for a back up and just buying a CO2 cylinder. I doubt the mixing will go smoothly either. ...
  11. IIRC, they use a different valve on C)2 tanks. ...

    IIRC, they use a different valve on C)2 tanks. You would probably be just about as well off keeping the 80 for a back up and just buying a CO2 cylinder.
  12. Replies
    7
    Views
    3,839

    A big problem is that Aluminum doesn't let you...

    A big problem is that Aluminum doesn't let you see the puddle like steel. I have an Alcoa Aluminum welding book from the 1950s; it is interesting to read, but there isn't a practical reason IMO for...
  13. Replies
    2
    Views
    2,865

    Check out Western for a fitting. They sell the...

    Check out Western for a fitting. They sell the parts needed for the QD fitting on the 42i and 200EX.
  14. Replies
    24
    Views
    9,839

    I asked him the same question on another forum. ...

    I asked him the same question on another forum. He likes the foot pedal on the 186, but other than that, he likes the 200EX better.
  15. Replies
    7
    Views
    2,237

    Congratulations. I know the 62i is a beast, but...

    Congratulations. I know the 62i is a beast, but the 42i will cut anything I need.
  16. Replies
    3
    Views
    3,826

    Are you running gas?

    Are you running gas?
  17. Replies
    11
    Views
    6,883

    Actually, most DC is Reverse Polarity (DCEP). ...

    Actually, most DC is Reverse Polarity (DCEP). Actually, I made a mistake in my post, but it was too late to correct it. I usually use electrode + for AC on this machine. Since AC alternates, it...
  18. Replies
    11
    Views
    6,883

    Old thread, but it brings up a question I have...

    Old thread, but it brings up a question I have had since I got the 200EX. In AC Stick mode, does it matter whether you connect the stinger to the + or - connection? I have always plugged it in the-...
  19. Replies
    7
    Views
    1,895

    Very nice. I have a Jet 4x6 which looks like...

    Very nice. I have a Jet 4x6 which looks like your HF, but is much better made. I have never broken a blade with it. I barely have room for the small saw, no way to fit that monster in my garage.
  20. Replies
    25
    Views
    20,104

    Nice design and fabrication.

    Nice design and fabrication.
  21. Replies
    42
    Views
    83,198

    Very nice workmanship and creativity on your...

    Very nice workmanship and creativity on your projects.

    It would seem that your open air shop would be vulnerable to rain and wind. How do you protect it?
  22. Replies
    7
    Views
    4,787

    Crazy! My LWS will swap out for the difference...

    Crazy! My LWS will swap out for the difference in the cost of the bottles. That said, you can do a lot of welding with an 80.
  23. Thread: 200i Foot Pedal

    by Cope
    Replies
    21
    Views
    8,097

    Daniel said he would ship it to me first so I...

    Daniel said he would ship it to me first so I could check it out for you. ;)
  24. Thread: 200i Foot Pedal

    by Cope
    Replies
    21
    Views
    8,097

    Now that's good service!

    Now that's good service!
  25. Thread: Slap Shot!

    by Cope
    Replies
    8
    Views
    4,656

    Maybe because he's a southpaw! Cool design and...

    Maybe because he's a southpaw! Cool design and fabrication. I really like my 200EX, but if I had the extra cash, I'd have the 200i just because.
Results 1 to 25 of 377
Page 1 of 16 1 2 3 4