FreeWeldingForum.com 
Welding Forum Community presented by LONGEVITY
877 - Long - Inc | 877.566.4462
Page 1 of 16 12311 ... LastLast
Threads 1 to 20 of 310

Forum: Plasma Cutting

General tips, ideas, tricks, and basic introduction on how to use Plasma Cutters.

  1. Sticky Thread Sticky: Plasma Cutting charts from the web

    Started by acourtjester, 05-19-2013 09:08 AM
    • Replies: 3
    • Views: 8,970
    08-24-2016, 05:34 AM Go to last post
  2. Sticky Thread Sticky: Force Cut 42i

    Started by Cope, 01-18-2013 04:46 AM
    9 Pages
    1 2 3 ... 9
    • Replies: 87
    • Views: 39,508
    01-04-2015, 08:15 AM Go to last post
  3. Sticky Thread Sticky: Plasma cutting gasses

    Started by WookieWelding, 02-10-2011 01:47 AM
    • Replies: 9
    • Views: 12,747
    10-22-2014, 01:09 PM Go to last post
  4. Sticky Thread Sticky: Excellent plasma cutting instruction videos

    Started by Gadget, 12-10-2010 05:53 PM
    • Replies: 5
    • Views: 8,998
    03-19-2013, 03:37 PM Go to last post
  1. Conversion from contact to pilot arc ignition

    Started by atlantis, 12-14-2016 08:47 AM
    • Replies: 2
    • Views: 1,312
    12-15-2016, 05:50 AM Go to last post
  2. Difference between HF and Pilot arc

    Started by Nicholas, 11-18-2011 06:23 PM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 20,101
    11-01-2016, 08:59 PM Go to last post
  3. Blue LP 50D pilot arc plasma?

    Started by anorad, 11-21-2015 08:12 AM
    • Replies: 6
    • Views: 1,277
    10-03-2016, 05:38 PM Go to last post
  4. Force Cut 42i and Baileigh PT-22 Plasma Table

    Started by WTC, 08-30-2016 01:52 PM
    • Replies: 0
    • Views: 1,435
    08-30-2016, 01:52 PM Go to last post
  5. 80i torch

    Started by nmugzy41, 06-26-2016 06:38 AM
    • Replies: 3
    • Views: 1,953
    06-29-2016, 05:34 AM Go to last post
  6. Consumables for the PT60 hand torch??

    Started by blueriver, 06-18-2014 08:11 AM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 9,358
    05-31-2016, 05:34 AM Go to last post
  7. Question Problem with motherboard on Hypertherm MAX PRO 200

    Started by Jan, 05-25-2016 01:06 AM
    • Replies: 0
    • Views: 383
    05-25-2016, 01:06 AM Go to last post
  8. Plasma cutter arcs but will not cut.

    Started by Gumby88, 07-03-2011 05:18 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 9,653
    05-17-2016, 02:41 PM Go to last post
  9. Unhappy hagar

    Started by hagar, 04-28-2016 04:24 PM
    • Replies: 0
    • Views: 429
    04-28-2016, 04:24 PM Go to last post
  10. Cutmaster 38 Regulator Replacement - Cheap

    Started by buddy in texas, 03-09-2016 10:41 AM
    • Replies: 1
    • Views: 837
    03-10-2016, 06:07 AM Go to last post
  11. Cutmaster 52 with Proma 150 THC Help needed

    Started by AnthonyHSF, 12-20-2015 02:19 PM
    • Replies: 6
    • Views: 1,836
    12-22-2015, 02:09 PM Go to last post
  12. no arc

    Started by johnnyg, 11-30-2015 11:36 AM
    • Replies: 2
    • Views: 931
    12-01-2015, 05:41 AM Go to last post
  13. longevity forcecut 62i

    Started by dzljon, 02-27-2015 04:28 PM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 6,927
    03-29-2015, 02:06 PM Go to last post
  14. air connections

    Started by crawlintoy, 03-15-2015 10:12 AM
    • Replies: 2
    • Views: 1,576
    03-15-2015, 03:34 PM Go to last post
  15. Question Plasma getting ignition faults (ESAB ESP-100i)

    Started by choover73, 03-10-2015 03:10 PM
    • Replies: 1
    • Views: 1,252
    03-10-2015, 07:58 PM Go to last post
  16. cutting shapes

    Started by Tigmaniac, 12-02-2014 05:05 AM
    • Replies: 6
    • Views: 3,498
    02-18-2015, 09:45 AM Go to last post
  17. NAPA Model 83-329 plasma cutter manual

    Started by Pipinchaz, 01-18-2015 07:07 PM
    • Replies: 1
    • Views: 2,003
    01-19-2015, 10:20 AM Go to last post
  18. Force Cut 42i Air/CFM Requirements

    Started by motofool33, 12-13-2014 10:22 AM
    2 Pages
    1 2
    • Replies: 19
    • Views: 6,180
    01-04-2015, 07:59 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •